Kazama has released a lower suspension adapter. This is the part that changes the low damper mounting position of suspension arms side. Available in ma and black.

Was packed around the width, to expand the adjustment range of the wheel base, we are up the freedom of caster angle setting. Even in narrow scrub setting up and turning angle, I adopt the design to avoid the interference of the lower arm and tire. Course performance, with machined aluminum body with an emphasis on coolness and rigidity, dress-up effect is also excellent. I lineup and 2.5mm shaft specification corresponding to Doripake, a 3mm shaft specification corresponding to Ribasasu system.

Is Vacula aluminum rear upright. It allows you to drift stable running to minimize alignment changes by an aluminum lightweight and high rigidity. In addition, upper arm mounting position for three places set. Be attached to the outside of the original position is also possible, it is possible to obtain a higher rear grip. I is set at 0 degrees toe angle.

Active Hobby has released a steel adjustable drift shaft/axle/CVD for 3 different chassis setup suspensions. The Yokomo drift package, Tamiya and OTA-R31.
The Tamiya and OTA version will come with steering angle of 60 degrees. and the Yokomo will have 65. 
They all are adjustable by single increment to 10. 
Tamiya will be 43 to 53mm in length, Yokomo 47 to 57mm and OTA 45 to 55mm. There are easy markings to make even adjustments.        

Tammiya and OTA design

Yokomo design.

It is the aluminum servo mount units that are connected by a strut bar servo mount two, increased the mounting rigidity. I can attach and Tamiya · TT-02, for example, Yokomo · DIB. (Use low height servo Portrait) 　by adjusting the height 3x6mm or spacer, (※ spacer is sold separately) Standard servo also supports supports the delicate steering work in direct from. It is also possible that a small processing such as sharpen the interference part, to mount such Doripake, in all models

silver, black, blue, red, light blue, and gun metal.

A step-adjustable link adoption! 
Doripake aluminum steering crank set up! ! It is the appearance of the Doripake aluminum steering crank. Set to 3 places the tie rod mounting position in order to respond to the situation and run various. In addition, I adopt a step-adjustable link that allows you to set up a small quantitative. Steering link adjustable length in 0.5mm increments is based on allows for quick and accurate setting change. It becomes possible to set up Ackermann ratio perfect in combination with OD1298 Aluminum C hub and upright set, but, in combination with the normal upright is also possible of course.

Finally here! Doripake for positive scan set! ! It is the appearance of the Doripake Aluminum C hub-and-light set-up. Caster, kingpin angle both set to 8 ° with the reputation. Further, the optimization reduces the scrub radius by adopting the R31's axle shaft. Furthermore, can be set to an optimal ratio Akerman In conjunction with OD1252 Aluminum Steering crankset released simultaneously. It is the completion of a perfect steering geometry OD think. In addition, the diversion to the DRB or the like has become possible as well as a possible adjustment of the wheelbase a spacer provided

Rear Suspension arm of Vacula unique shock mounting portion became a separate body. By replacing this product this separate block, can be adjusted in six steps in 2mm pitch shock mounting position. It is possible to change quickly without having to reverse the suspension arms.

Yeah Racing has released the competition damper! On a final testing stage. Today, our product engineer is testing the O-ring to make sure it seals perfectly to avoid oil leakage!

Yeah Racing Shock-Gear Damper

These dampers are made of high quality aluminum, titan coated damper shafts and features a unique piston design.

In this Shock-Gear damper series, it features a unique piston design, 3 expert tuning modes are available to fine tune damper's response. It also has a rebound core system, which allows customers to adjust for 4 rebound rate: 25%, 50%, 75%, 100%.

The titan coated damper shafts are adopted to reduce the friction and offer better reaction! O-ring is also sealed perfectly to avoid oil leakage!

From Italy comes the AE86 Body Kit by Exstreme Sports. The kit works with all HPI AE86 Levin and Trueno shells. These fenders can also be modded to fit other chassis as well.
Each kit includes 4 pcs: 2x front fender and 2x rear fender. Kit comes clear & unpainted. It requires trimming and painting.
Mounting screws are not included.
These are available in limited quantities.
If interested below is the contact info

[email protected]